I recently picked up a La San Marco SM 95

It had previously been sitting in a basement collecting dust for at least a year and a half.

I brought it home and noticed it had a really funny smell... I think it was probably REALLY rancid Coffee oils. I took it apart and cleaned it all out. Then I ran some rice though it, then some coffee. And it seems to be working fine... but it still has a hint of that funny smell. Any ideas on what the next step should be to clean it??

Views: 466

Attachments:

Reply to This

Replies to This Discussion

I already did that.. It helped... but it's still not 100%

I guess I ran about a 1/4 of a bag. Do you think I should just run a whole bag more though?
That's a good call. I never thought of Dollar store rice...

If that doesn't work does anyone know of any other ways to clean out an old grinder?
I actually have done that too. I included the schematics for the grinder in the initial post. Is there a cleaning solution or item that would be safe to use on the parts??
MINUTE rice is good (raw rice.. I'm not sure I'd go that route).

Grindz is good.

But nothing tops good old fashioned elbow grease and dismantling the thing to get at it with a brush. I've done this a few times myself. Even on old grinders with a persistent funny smell.

I remember them taking a variety of treatments. (the three mentioned above, and probably some other things I'm not remembering)
Thanks for all the responses. I cleaned out the grinding chamber with a brush that came with another grinder I have, and it worked pretty well. I guess I was just curious if there is a safe solution people have heard of that could act as a degreaser without having any adverse effect of the performance of flavor of the grinder. It might be just a situation where I have to just keep cleaning (I've already been cleaning it for a total of near 10 hours!!)...

If nothing else I at least have a deep spiritual connection with the grinder at this point! I was thinking about selling it, but we've bonded so much at this point it might be hard ;-)
contact the guys at URNEX, they have a good grinder cleaner that should sort the problem..
if you are going to use a metal brush, make suere it is a soft metal. So you don't scratch up your grinder and give the oils even more places to go.
Yeah I was thinking about grindz... but I think rice works just about as well...

I noticed UNEX also has a product called cafe wipz in their grinder section, but that doesn't look like it would be good for the grinder parts.. does anyone have any experiance with these things?

Jason said:
contact the guys at URNEX, they have a good grinder cleaner that should sort the problem..
Hi Billy. Eucchhh! That smell... coming back to me even now. I think we've all been there.

Can you pinpoint where the smell is coming from? Could be something inside the grinder too (like in with the motor). Also if you haven't done it, go at it with a shop vac. That'll pull out lots of stuff from places your brush would never reach. Also, plastic will pick up bad smells and take a long time to let them go. Pinpointing exactly which parts are still funky will give you a better idea of how to proceed. Any visible film on any parts?

You say you took it apart, but how far? I was shocked at how much stuff had accumulated under the doser vanes, between the doser body and the grinder, and how funky the spongy gasket material between the doser and body smelled. You probably stripped it pretty good, but thought I'd mention it just in case.

Also, its possible it just needs to air out a little. Maybe leave it apart and exposed to clean air for a few days?

Does it impart this funky flavor to the rice?

I'd definitely say (except on plastic parts) use wet, chemical, or abrasive cleaning methods only as a last resort. Good old soap and water on the parts that can get wet does wonders.

Just a few thoughts. Hope they help. Good luck.

b
Take the thing apart and soak all the parts you can in Cafiza, Order fresh blades and reassemble.
This is what I was going to say. I've done it to probably 5 different used grinders now. You normally want new burrs when you receive an old grinder anyway, so I normally plan on purchasing them from the get-go. Other than that, Cafiza works wonders. Make sure you have a really great idea how the thing goes back together before you take all of the parts off. Don't make it a long soak either. I normally start sort of an assembly line of soaking and scrubbing. I put in a few parts and let them soak for 15 minutes or so, then remove them and add some new parts (keeping different "areas" of the grinder soaking together, so as to avoid as many... uh... "extra" parts as possible) and while the new parts are soaking I scrub the ones that just came out with some sort of stiff nylon brush. This method has never failed me. I normally leave at least a day for all of this to happen, so it's no easy process. Also, make sure that you have an extra fan around somewhere and that you can lay the parts out under the fan to dry for probably 8 hours or so. You *don't* want to reassemble wet parts.

HTH
-Bry

Jason Shipley said:
Take the thing apart and soak all the parts you can in Cafiza, Order fresh blades and reassemble.
I found using those portable steamers can do wonders with removing coffee oils on your grinder. Also oxyclean does a pretty good job at cleaning things....smells and works just like URNEX or purocafe

Reply to Discussion

RSS

Barista Exchange Partners

Barista Exchange Friends

Keep Barista Exchange Free

Are you enjoying Barista Exchange? Is it helping you promote your business and helping you network in this great industry? Donate today to keep it free to all members. Supporters can join the "Supporters Group" with a donation. Thanks!

Clicky Web Analytics

© 2024   Created by Matt Milletto.   Powered by

Badges  |  Report an Issue  |  Terms of Service